Hj-6 Laptop Phone Battery 3-20c/Min Rapid Rate Change Temperature High Low Temperature Cycle Test Chamber
Climate controlled cycling environmental temperature humidity test chamber is for testing material heat, cold, dry resistance, humidity resistance.Suitable for electronics, electrical appliances,Communications, instrumentation, vehicles, plastic products, metal, food, chemical,building materials, medical, aerospaceand other products.
1. High-quality appearance, the body adopts arc shape, the surface is treated with matte stripes, and the flat non-reaction handle is used, which is easy to operate, safe and reliable
2. The rectangular double-layer glass viewing window can be used to observe the test items during the test. The viewing window is equipped with an anti-sweat electric heater device to prevent water vapor from condensing and water droplets, and high-brightness PI fluorescent lamps keep the interior of the box illuminated.
3. It has a test hole for external test power cord or signal line and an up and down adjustable storage tray. Box door Double-layer insulation and tight airtight, which can effectively isolate internal temperature leakage
4. With an external water supply system, it is convenient to supplement the water supply of the humidification barrel, and it can be recycled and used automatically.
5. The compressor circulation system adopts the French “Taikang” brand, which can effectively remove the lubricating oil between the condenser tube and the capillary tube.
6. The controller adopts an imported 7-inch touch screen, which can display the measured value and the set value at the same time. The temperature and humidity test conditions are programmable. The test data supports USB direct export, and the maximum recording time is 3 months.
7. The built-in moving pulley is easy to move and place and has a strong positioning screw to fix the position.
“GB/T 2423.2-2001 Test B: High temperature test method
GJB 150.3-1986 High temperature test
IEC68-2-2 Test B: Dry Heat. GB 11158 “Technical Conditions for High Temperature Test Chamber”
GB10586-1 “Technical Conditions of Damp Heat Test Chamber”
GB/T 2423.2 “Basic Environmental Test Procedures for Electrical and Electronic Products Test B: High Temperature Test Methods”.
GB/T 2423.3 “Basic Environmental Test Procedures for Electrical and Electronic Products Test Ca: Constant Damp Heat Test Method”. Etc..
|Model||TH-80(A~F)||TH-150(A~ F)||TH-225(A~F)||TH-408(A~F)||TH-800(A~ F)||TH-1000(A~F)|
|Internal Dimensions W x H x D(cm)||40x50x40||50 x 60 x 50||60 x 75 x 50||80 x 85 x60||100x100x80||100x100x100|
|External Dimensions W x H x D(cm)||120x165x115||130x170x125||140x185x130||165x195x155||185x200x175||190x210x185|
|Temperature range||Low temperature: A:+25°CB:0°C, C:-20°C, D:-40°C, E: -60°C,F:-70°C ) High temperature:100°C (150°C )|
|Humidity range||20%~98% R.H. ( 10%~98%R.H ) ; (5%~98%R.H is a special selection condition)|
|Temperature and humidity analysis
|0.1°C 0.1%R.H./±2.0°C ±3.0%R.H.|
|Temperature and humidity
|heating/cooling time||Heating up about 4.0°C/min; cooling down about 1.0°C/min|
|Internal and external materials||The inner and outer boxes are made of SUS304# stainless steel plate (optional paint)|
|Insulation material||High temperature resistant high density ethyl chloroformate foam insulation material|
|Cooling system||Air-cooled/single-stage compressor (-20°C); two-stage compressor (-40°C-70°C)|
|Safety protection device||No fuse switch, compressor overload protection, refrigerant high and low pressure protection, over-humidity over-temperature protection, fuse, fault warning system, water shortage alarm protection|
|Accessories||Operation hole built-in glass door (optional), recorder (optional), viewing window, 50mm test hole,
PL box light, partition, dry and wet ball gauze, casters, leveling stand
|Power supply||AC220V 50/60Hz & 1∮ AC380V 50/60Hz3∮|